Designing Masonry Walls for Metal Buildings Concord NC

If the top and bottom of the wall are continuously supported, then the masonry wall will span 12 feet vertically.If you cannot use the roof structure to support the top edge of the wall, install a very stiff steel beam or a beam combined with horizontal reinforcement in the top several feet of the wall.

D & D's Flooring & Interiors
(704) 684-4887
628 West Morehead Street
Charlotte, NC
Services
Formerly The Plywood Mart, Inc.; Mohawk® carpet, hardwood, laminate, resilient and tile flooring; Shaw® carpet, hardwood, laminate, resilient and tile flooring; Armstrong® hardwood, laminate and resilient flooring; Bruce® hardwood flooring; custom site finished hardwood floors (custom colors and designs available); Daltile® tile and stone; Crossville® tile and stone; Florida® tile and stone; Marazzi USA® tile and stone; Andersen® windows and doors; Marvin® windows and doors; Santa Cruz®
Membership Organizations
Homeowner Approved, National Wood Flooring Association Member.

Data Provided by:
Stonebridge Yards
(919) 267-5121
109 Parkcanyon Ln
Cary, NC
 
Buckner'S Masonry & Construction
(336) 906-2431
5815 Samet Dr Ste 103
High Point, NC
 
Masonry At
(919) 957-7879
411 E End Ave
Durham, NC
 
Custom Edge Inc
(910) 308-1399
2766 George Owen Rd
Fayetteville, NC
 
Preferred Carpet One
(704) 271-1397
5001 South Boulevard, Suite E
Charlotte, NC
Services
Product only, or product plus installation. Hardwood floors: All species and types, solid and engineered, unfinished and prefinished laminate floors, cork floors and bamboo floors; hardwood sanding and refinishing. Other flooring: Marmoleum, sheet vinyl, luxury vinyl V.C.T., rubber floors, cove base. Carpet: All carpet types for residential and commercial; custom area rugs, stair runners and outdoor carpets. Stone: Travertine, slate and exotic stone, granite floors, ceramic, porcelain, glass til
Membership Organizations
Homeowner Approved, Allen Tate Concierge Services.

Data Provided by:
Williams Masonry & Concrete, Inc.
(910) 470-6777
1404 Corbett St.
Wilmington, NC
 
Pro-Site Services Llc
(919) 667-9790
800 N Mangum St
Durham, NC
 
Abc Masonry Construction Inc
(910) 483-2490
3385 Stanworth Dr
Fayetteville, NC
 
Hester'S Masonry
(919) 956-7936
2416 Lindmont Ave
Durham, NC
 
Data Provided by:

Designing Masonry Walls for Metal Buildings

Provided By:

Source: MASONRY CONSTRUCTION MAGAZINE
Publication date: October 1, 1991

One of our current projects is a pre-engineered metal building with a 12-foot eave height. The rigid frames are 30 feet on center. The exterior walls are 8-inch concrete masonry, to be supported at the top with a structural steel member spanning 30 feet between frames. Horizontal deflection of the top wall support and the rigid frame must be considered together. What are your minimum deflection recommendations? Can the concrete masonry tolerate greater than L/600 deflections?
A simple, efficient way to control deflection along the top edge of the wall is to design and detail the roof structure to act as a diaphragm, rather than to design a beam spanning 30 feet. If the top and bottom of the wall are continuously supported, then the masonry wall will span 12 feet vertically.If you cannot use the roof structure to support the top edge of the wall, install a very stiff steel beam or a beam combined with horizontal reinforcement in the top several feet of the wall. In either case, don't use rule-of-thumb deflection limitations to design the beam. Instead, design the steel beam stiff enough to prevent stresses in the wall from exceeding levels allowed by code. The percentage of loads handled by the masonry should be based on relative stiffness. The size of the steel beam may be reduced greatly by using reinforced masonry in conjunction with the beam.

Click here to read full article from Masonry Construction